Menvier Security TS790+ Dokumentacja Pobierz pdf (Strona 26)

System Installation TS790+ & TS900+ Installation Manual

Power-Up Checks

When the initial power-up checks have been

completed, check the following:

1. Switch off the 240V mains supply and

measure the DC voltage at each Node and

remote keypad and ensure the voltage is

greater than 12.8V whilst the system is

powered from its standby battery.

2. Switch on the 240V mains supply and

measure the DC voltage between the mains

earth connection and AUX +12V. Then

measure the DC voltage between the mains

earth connection and AUX 0V. In both cases

the measurement should be 1V or less. If the

voltage is greater than 1V, the system has

an “Earth Fault” and all cables should be

checked for isolation to Earth.

3. Using a voltmeter measure the DC voltage

across the control panel PCB test points (V)

and calculate the system current

consumption (see page 8). Ensure that the

reading is not greater than 1.5A.

4. Repeat test (3) with the system in an alarm

condition and ensure that the reading is not

greater than 1.5A.

The TS790+ & TS900+ have an

overload protection circuit. If the power

supply is overloaded, the display will

show: “PSU OVERLOAD ! ! !” and sounder

will sound.

NVM Defaults

Section Option Default

User 00 Engineer 1234

User 01 Master 5678

User

Codes

User 02 - 31 Not Used

Panel Output 1 Walk Test (004)

Panel Output 2 Courtesy Light (012)

Panel Output 3 Switch 12V (002)

Panel Output 4 Detector Reset (003)

Panel Output 5 KP1 Code Accepted (009)

Panel Output 6 KP1 Code Accepted (009)

Panel Output 7 KP2 Code Accepted (009)

Panel

Outputs

Panel Output 8 KP2 Code Accepted (009)

Digicom Output 1 Fire (007)

Digicom Output 2 PA (006)

Digicom Output 3 Alarm (005)

Digicom Output 4 System Set (008)

Digicom Output 5 Active Omit (080)

Digicom Output 6 Bell (000)

Digicom Output 7 Confirmed Alarm (011)

Digicom

Outputs

Digicom Output 8

Tamper Fault (020)

Digi Channel 1 Fire (007)

Digi Channel 2 PA (006)

Digi Channel 3 Alarm (005)

Digi Channel 4 System Set (008)

Digi Channel 5 Active Omit (080)

Digi Channel 6 Bell (000)

Digi Channel 7 Confirmed Alarm (011)

Digi

Channels

Digi Channel 8 Tamper Fault (020)

XNode Output 1 Walk Test (004)

XNode Output 2 Courtesy Light (012)

XNode Output 3 Switch 12V (002)

XNode Output 4 Detector Reset (003)

XNode Output 5 Code Accepted (009)

XNode Output 6 Code Accepted (009)

XNode Output 7 Code Accepted (009)

XNode Output 8 Code Accepted (009)

XNode Output 9 Code Accepted (009)

XNode

Outputs

XNode Output 10 Code Accepted (009)

Circuit 01 Final Exit

Circuit 02 Night (Access)

Circuit 03 - 06 Night

Circuit 07 Exit Terminator

Circuit 08 PA Audible

Circuit 09 (Kpd 1) Final Exit

Circuit 10 (Kpd 1) PA Audible

Circuits

Circuit 11 - 56 Not Used

00 Test Call At 000 hours

01 No of Re-arms 000

02 Settle Time 007 seconds

03 Part Set Coms Dly 000 seconds

04 Exit Time 030 seconds

05 Entry Time 015 seconds

06 Bell Duration 020 minutes

07 Bell Delay 000 minutes

08 D-Knock Delay 008 seconds

09 Test Time 014 days

System

Timers

10 Second Entry 000 seconds

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 69 70

Komentarze do niniejszej Instrukcji

Brak uwag