Menvier Security TS700 Dokumentacja Strona 29
- Strona / 68
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Program Circuits
The TS790 can monitor up to 16 detection circuits,
whereas theTS900can monitor upto 56detection
circuits.Eachcircuitmustbeprogrammedinorder
for the system to respond correctly.
Circuit Types
The circuit type defines how the circuit will respond
when it is triggered. The following circuit types are
available:
0 Not Used
A circuit that will never generate any alarm.
1 Night
Acircuitthat willgenerate afullalarmwhenthe
system is set.
2 24hr
A circuit which is monitored at all times. When
triggered in the unset condition a local alarm
is generated and when triggered in the set
condition a full alarm is generated.
3 PA Silent
A circuit which is monitored at all times. When
triggered it will activate any outputs that are
programmed as P.A.
4 PA Audible
A circuit which is monitored at all times. When
triggered it will activate any outputs that are
programmedasP.A.andgenerateafullalarm
condition.
5 Fire
Acircuitthat isnormallyconnectedto asmoke
detector. When triggered it will generate a fire
tone on the internal sounders, the external
sounders are pulsed for the bell duration and
any outputs programmed as fire will be
activated.
6 Auxiliary
A circuit which is monitored at all times. When
triggered it will activate any outputs
programmed as Auxiliary.
7 Final Exit
This must be the first detector or door contact
that is triggered when entering the protected
area. When the setting mode for the system is
programmedforFinalExitsetting,openingand
closing of this circuit during the exit procedure
will cause the system to set. Once set,
activation of this circuit will start the entry timer.
8 Exit Terminator
A circuit that is normally connected to a push
button outside the protected premises, which
can be used to finally set the system or area.
9 Keypoint
Acircuitthatmaybeconnectedtoakeyswitch
to allow setting and/or part-setting of the
system.
The Key Point circuit has two groups of
attributes. The first group of attributes control
the wards that are set/unset when the circuit is
switched between “Healthy” and “Active”. The
second group of attributes control the wards
that are set/unset when the circuit is switched
between “Healthy” and “Shorted”.
When programming the Key Point circuit the
eight standard attributes are not available,
insteadtheattributesareusedtoselecttheKey
Point operation as follows:
[1] Full Set Group - “Healthy” to “Active”.
[2] Code Set Group A - “Healthy” to “Active”.
[3] Code Set Group B - “Healthy” to “Active”.
[4] Code Set Group C - “Healthy” to “Active”.
[5] Full Set Group - “Healthy” to “Shorted”.
[6] Code Set Group A - “Healthy” to “Shorted”.
[7] Code Set Group B - “Healthy” to “Shorted”.
[8] Code Set Group C - “Healthy” to “Shorted”.
If the “Key Point” is not assigned to any of the
above options, the circuit becomes a
“Monitored” circuit. A “Monitored” circuit is
monitored at all times. When triggered it will
activate any outputs that are programmed as
Timed Output and log the event.
A PSU-Battery
This circuit may be connected to the 519XB
power supply via the 519 FM PCB to allow the
monitoring of the standby battery. See
“Monitoring a Power Supply” on page 18.
B PSU-Fuse
This circuit may be connected to the 519XB
power supply via the 519 FM PCB to allow the
monitoring of the standby battery. See
“Monitoring a Power Supply” on page 18.
C PSU-Power
This circuit may be connected to the 519XB
power supply via the 519 FM PCB to allow the
monitoring of the mains power failure. See
“Monitoring a Power Supply” on page 18.
TS900 Installation Manual Engineer's Menu 1
25
- TS790 & TS900 1
- Contents 3
- Engineers Menu 3 4
- Appendices 4
- Overview 5
- Remote Keypads 6
- TS900 NODE 6
- ID Node (TS900.IDNODE) 6
- TS700 LEC 6
- Specifications 6
- Cable Routing 7
- Remote Network Wiring 8
- Control Panel Installation 9
- Control Panel PCB Layout 10
- TS900 LCD Remote Keypad 12
- TS790 Star Remote Keypad 12
- TS700 LED Remote Keypad 13
- TS700 Remote Arming Station 13
- Installation Procedure 13
- Engineer’s Keypad 14
- TS900 Node Layout 15
- Double Pole 16
- End Of Line 17
- Auxiliary Tamper 18
- Extension Loudspeakers 18
- Digicom/RedCARE Installation 19
- Plug-on Digicom Installation 19
- Using the CPA6 Printer 20
- Control Panel Outputs 21
- Node Outputs 21
- Pre Power-Up Checks 22
- Initial Power-Up 22
- Power-Up Checks 23
- NVM Defaults 23
- Engineer’s Menu 1 25
- Menu contents 25
- Panel Outputs 26
- Digicom Outputs 26
- Digicom Channels 26
- Programmable Output Types 26
- Circuit Types 29
- Circuit Attributes 30
- System Timers 31
- StarburstLCD 34
- Remote Reset Algorithm 35
- Configuration 35
- View Location Text (LCD Only) 38
- Engineer's Menu 2 39
- Menu Contents 39
- View Circuits 40
- Set System Time 40
- Set System Date 40
- Change Passcode 40
- Log Event Codes 42
- View System Log 42
- Reset User Code 1 44
- Start Call Back 44
- Time Switches 46
- Part Set Group Operation 47
- Code Set Group Operation 47
- Reset Message 48
- Banner Message 48
- Built In Tests 49
- View Inactive Circuits 50
- Custom Outputs A & B 51
- Modem Options (LCD Only) 52
- Program Digi Flowchart 53
- Reset Digicom 54
- Workshop Canteen 59
- Service Department 59
- Key Point Application Example 60
- Control Panel 61
- Text Editing Keys 62
- TS790/TS900 62
- User Types 63
- Setup New Users Flowchart 64
- Engineers Menus 66
- User Menus 66
- SECURITY 68
Asus CUVL-VM manuales
Manuales del propietario y guías del usuario para Placas base Asus CUVL-VM.
Ofrecemos 1 manuales en pdf Asus CUVL-VM para descargar gratis por tipos de documentos: Manual de usuario
Komentarze do niniejszej Instrukcji